Every part you could know on the best way to make and stain 2″ x 6″ lumber right into a DIY giant spherical wooden desk prime utilizing a round noticed. No fancy cuts or different saws wanted. Additionally, learn to combine stains and paint to get simply the correct coloration and aged end that you just wish to obtain on the wooden.
Chances are you’ll be asking why I needed a brand new eating desk for my kitchen after I not too long ago made excessive with paint to seem like it was made from zinc.
I appreciated how the zinc end got here out, however actually needed a bigger desk for when we’ve got greater than 4 folks on the desk.
The desk is 46″ spherical and when you set it with plates, there isn’t quite a lot of house left for a centerpiece or for serving plates of meals.
In my earlier house’s eating room, I had a plywood desk prime extender that went proper over the desk once we wanted to seat greater than 6 folks. It was an excellent choice to have.
The eating part of my kitchen is 8′ x 10′ so I knew a barely bigger prime might work.
My kitchen desk has a protracted historical past. I purchased it for $150 at JC Penneys once we first moved to our Pennsylvania home 27 years in the past.
- The desk received its first makeover about 10 years later once I stripped the darkish end to make it look uncooked and whitewashed.
- Then a number of years after that I painted the black metallic base, white.
- After this I added the bulletin board paper to make the desk prime seem like it was made from wooden boards. I actually appreciated this and what I believed could be a short lived protecting, ended up lasting nearly a 12 months. It additionally confirmed me that I like a extra rustic prime for the desk.
- Its final makeover was once I used a pretend zinc portray end on the highest.
Why I Like a Spherical Eating Desk
My new DIY 60″ spherical wooden desk prime
My kitchen eating space is sq. so a spherical desk works higher. I might use a sq., however that will add extra straight strains and be awkward to stroll round. A round form is simple to stroll round and provides just a little form distinction to all of the straight strains within the cupboards and partitions.
A spherical desk additionally makes for higher dialog and an excellent form when enjoying board and card video games with a bunch.
I favor a pedestal base on a spherical desk or a base like mine that’s centered, no legs close to the sting of the desk to get in the best way of the chairs or to must straddle your legs round.
I made a decision after taking a look at many new spherical tables, that I actually appreciated the desk base on my desk, simply not the dimensions of the highest anymore. I like that the bottom doesn’t take up quite a lot of visible house and you may see by means of the bottom, which makes the house seem bigger.
Time for me to do a reasonably simple DIY woodworking undertaking.
The right way to Make a Spherical Wooden Desk Prime Utilizing 2″ x 6″ Pine Boards
The instructions to make a spherical wooden desk utilizing 2″ x 6″ boards might be made to any diameter. For my instructions, I’m itemizing the quantity of wooden and pocket screws that I wanted to make a 60″ diameter spherical wooden desk prime. Alter the quantity of wooden and screws wanted for the dimensions desk prime you need.
In the event you don’t have an current desk base as I did, one might be simply DIY’ed. See the hyperlinks under to the spherical desk making movies that I watched to choose up recommendations on the best way to make a spherical wooden desk prime.
After watching the spherical desk making movies under, I made a decision to observe Knock-Off-Wooden’s video utilizing a round noticed and easy DIY jig, however I used 2″ x 6″ boards as an alternative. I didn’t want so as to add the additional thickness across the outdoors fringe of the desk as they did.
DIY Wooden Spherical Desk Prime Movies to Watch:
- Spherical Farmhouse Desk and Base
- Two Methods to Make a Spherical Desk
- Slicing Out a Spherical Desk Utilizing a Round Noticed
The right way to Use a Kreg R3 Jig
A Kreg R3 jig enormously simplifies the preliminary steps in making the desk. If in case you have by no means heard of this ingenious little software – here’s a video: The right way to Use a Kreg R3 Jig System
The final time I used my Kreg R3 Jig, I made my framed mirror prime espresso desk.
Provides Wanted:
For Wooden Desk Prime
- 12 – 2″ x 6″ x 6′ white pine boards – search for boards with fewer knots and which are straight
- Round noticed with wooden reducing blade
- Scrap wooden to make a easy wooden reducing jig – I used a bit of bead board and plywood
- Kreg R3 Pocket Gap Jig
- 100 – 8 x 2-1/2″ pocket gap screws
- Drill and Kreg jig drill bit that comes with the jig
- Wooden glue and 1″ huge paint brush
- Marking pen
- Sander and sandpaper with totally different grits – 80, 100, and 220
- Measuring tape
- Tack fabric
- Security goggles
For Distressing Wooden
- Hammer
- 7-In-One Device
- Small sections of metallic chain, paper clips, noticed blades, axe or any merchandise that may depart a dent within the wooden
For Stain and Sealer
I used all water-based merchandise since they don’t deliver out the yellow orange tones in pine.
- Wooden stain within the coloration of your selection – I combined the colours: Minwax Semi Clear Colour Stain (Enchanted Forest) with Varathane Basic Water-Primarily based Wooden Stain (Darkish Walnut) in equal measurements to get the colour I needed
- Water-Primarily based Pre-Stain Wooden Conditioner
- Glazing liquid
- Acrylic craft paints: Decor Arts Americana (Cobblestone) and People Artwork (Mushroom)
- 2 – 3″ huge paint brushes
- Blue Store Towels of lint free rags
- Polycrylic in a Matte end
The right way to Misery and Age Pine Boards So They Will Look Outdated
- Lay wooden boards on the ground. Inserting the higher aspect of every board face up. Even when the higher aspect has the model marking on it, this shall be sanded off later.
2. Placed on a pair of security googles and misery the higher aspect of every board utilizing a wide range of gadgets. A hammer, 7-In-One Device (not pictured), metallic chain, wooden screw, axe, or any sharp or tough edge merchandise you could find.
3. Lay the chain on a board and whack it with a hammer a number of occasions. Place the wooden screw on a bit of the board and use your foot to press laborious and roll it over the wooden in spots. Choose on the wooden with an axe to make fake worm holes. Repeat the method in a random approach on all of the boards.
3. As soon as every board has been distressed, use a sander with 100 grit sandpaper alongside the perimeters of every board to spherical the sting. Repeat for every board.
The right way to Assemble a Spherical Wooden Desk Prime
The right way to Make Pocket Holes To Connect the Boards
- Flip the boards so the nice aspect that you just distressed and sanded is face down.
- Choice: Use further boards alongside the ends of the boards on the ground on two sides to maintain the boards aligned.
2. Make marks with arrows pointing within the path the pocket holes shall be made alongside either side of every board. Place these about 6″ – 10″ inches aside. There must be an equal quantity of pocket holes stepping into every path on every board. These shall be the place you’ll make the pocket holes the place the screws will go in at an angle to connect the boards to one another.
Word: Just remember to should not going to position a screw the place the desk shall be reduce right into a circle and that the the boards on the outer fringe of the desk are the identical width on either side for symmetry. If you wish to be certain, line up the boards so they’re collectively. Discover the middle level and mark it.
- Tie a bit of string, half the size of your future desk prime’s diameter and fix it to a pencil. On the alternative finish of the string, use a push pin to connect the string to the middle level.
- Transfer the pencil so far as the string will go and draw a circle across the wooden. This may present you roughly the place the reduce line shall be. Keep away from including pocket holes near this round line.
Drilling all of the pocket holes is simple, however the course of will go sooner with two folks: one to arrange the jig at every arrow mark and the second to drill the holes into the wooden.
The picture above is from the Kreg web site. You’ll be able to see the pocket holes the jig makes on the correct.
Repeat the pocket gap making course of on each board.
The right way to Connect Pine Boards to Make the Spherical Wooden Desk Prime
- Beginning at one finish, brush the sting of the primary board with wooden glue evenly over your entire edge on one board.
2. Line the primary board up with the second board so they’re even on the ends and drive a pocket screw into every gap. This may deliver the 2 boards collectively very snugly with one another. Ensure that when placing the screws in that the boards are stage with one another on the ground.
3. Repeat this course of for each board, ensuring that the pocket holes and screws go in each instructions on every board.
4. Test after each hooked up board that the highest aspect is even. This may get tougher to examine as the highest will get bigger.
5. As soon as all boards are hooked up, transfer the desk to a piece bench or desk.
The right way to Minimize Hooked up Pine Boards Right into a Circle
- Make a jig in your round noticed utilizing scrap wooden. See particulars within the third video listed earlier within the submit. I used a bit of scrap bead board and trim molding to make my jig.
2. Discover the middle level on the desk prime and mark it. Make your jig in order that one finish might be screwed into the middle of the desk and the alternative aspect to connect and maintain the round noticed within the diameter in your desk.
3. Transfer the noticed across the desk prime just a little bit at a time. With each move, wooden will come off. The form is not going to be round but, however it can ultimately turn out to be a circle. It’s cool to see how this arrange works.
4. Upon getting accomplished tough cuts all the best way across the desk, repeat the method till the desk is spherical. It took me thrice round.
The right way to Stain a Spherical Wooden Desk Prime Utilizing Water-Primarily based Merchandise
- Flip the desk on the work bench so the highest aspect is now face up.
2. Sand the floor with 100 grit sandpaper to easy the highest and uncooked edges of the wooden.
3. If you wish to see extra distressing, use the sting of a painter’s 7-In-One Device to gouge the sting across the desk prime. Word that a few of what you added early might have been reduce off when the highest was reduce right into a circle.
4. When utilizing water-based merchandise on wooden, after sanding, clear the grit and spray the floor with water. Let sit a couple of minutes after which wipe extra off with a clear lint-free fabric. Wait till desk is totally dry after which sand as soon as once more utilizing 220 grit sandpaper. Clear off sanding grit.
5. Apply one coat of water-based Pre-Conditioner. Let it soak into the wooden for about 5 minutes after which wipe away the surplus.
I made my coloration stain right into a glaze so the stain could be extra clear and in addition give me extra time to wipe away the surplus and apply extra if wanted.
To Make the Staining Glaze: I used equal components of each colours of stain, glaze, and water. I combined it effectively in a plastic container and used a 3″ huge brush to use it to the desk.
6. Combine stain effectively and apply with a large brush. Wipe the surplus off straight away with a clear lint-free rag. Do two boards at a time and shortly wipe the surplus that will get overlapped on boards to maintain the colour even.
How I Selected The Stain Colour For the Desk
My kitchen and front room are open idea, however the house is just not giant. I discovered once I add too many colours to the house, it appears to be like cluttered.
I discovered the trick is to work inside a restricted coloration palette in order that the house doesn’t turn out to be too busy or look too cluttered. I made a decision to go together with a darker shade of wooden than the ground, so there could be just a bit distinction.
I needed to take away as a lot of the yellow and orange coloration from the wooden as potential. I did this by first mixing the stains to get a extra brown-grey coloration, however not too darkish.
After staining, I positioned a desk setting on the desk to see if I appreciated the best way it regarded. I additionally positioned a reclaimed board on the highest because it was closest to the ultimate coloration I needed.
I used acrylic craft paint over the stain whereas it was nonetheless damp so as to add extra gray to the stain coloration. That made it look extra just like the reclaimed board that has little to no yellow or orange tones in it.
I used a moist rag to use just a little little bit of the paint in random areas and wiped it away with lengthy pressured strokes to drive the colour into the wooden. I used just a little of each of those colours the place I believed the stain regarded too orange.
If I received an excessive amount of of a coloration wash in a single space, I used a really damp fabric to wipe a few of it away. Then I let it dry in a single day.
The right way to Connect the Spherical Wooden Desk Prime to an Current Desk Base
I hooked up my current metallic desk base to the brand new spherical prime. See the underside of the wooden desk? I used it as my stain coloration testing space. 🙂
- I sanded the stained desk very evenly with 220 grit sandpaper after which cleaned off the grit.
2. I brushed on one mild coat of Polycrylic in a Matte end and let it dry for 4 hours. I evenly sanded over the poly with 220 grit sandpaper once more. You should utilize a better quantity when you have it. Then, I cleaned off the grit and added a second coat. I repeated this course of once more for the third and ultimate coat of Polycrylic.
I like the way it turned out. See how the darkish stain will get into all of the distressing I did? 🙂
How To Look after the End On a Spherical Wooden Desk Prime
As soon as the end is cured – which may take a number of days to every week relying on the climate, you possibly can place plates and glasses of water on the desk with out the usage of a fabric or placemats. Spills can simply be wiped up.
I used a matte end on the desk. It does have a slight sheen when the sunshine hits it.
You Might Additionally Like:
- Completely Free Summer season Mantel Planter Field
- Driftwood Sculpture Desk Prime Stand DIY
- Wooden Slat Wall for My Residence’s Exterior
- Pin
- Fb
Put up navigation
Earlier Earlier Type Scouting: Vol. 39
Subsequent Proceed Berry Jam-No Sugar Recipe, My Kitchen Backyard & Wholesome Ideas – WFPB
